在建筑施工領域，電梯門套作為連接電梯井道與建筑墻體的關鍵構件，其防火性能直接關系到建筑整體消防安全。泰安地區工地使用的電梯門套是否具備防火特性，需從材料選擇、工藝標準及實際應用三個維度展開分析。

　　In the field of construction, elevator door frames serve as key components connecting elevator shafts and building walls, and their fire resistance directly affects the overall fire safety of the building. Whether the elevator door frames used in construction sites in Tai'an area have fire resistance characteristics needs to be analyzed from three dimensions: material selection, process standards, and practical application.

　　一、防火性能的材料基礎

　　1、 Material basis for fire resistance performance

　　電梯門套的防火性能主要由基材與表面處理工藝決定。當前主流材質包括：

　　The fire resistance of elevator door frames is mainly determined by the substrate and surface treatment process. The current mainstream materials include:

　　金屬復合材料：以鍍鋅鋼板或鋁合金為基材，內部填充巖棉、硅酸鋁等A級不燃材料。

　　Metal composite material: based on galvanized steel sheet or aluminum alloy, filled with A-level non combustible materials such as rock wool and aluminum silicate inside.

　　石材復合板：天然花崗巖或大理石與陶瓷薄板復合，耐火極限超2小時。泰安某高層住宅項目應用中，石材門套經消防部門專項檢測，火焰蔓延指數為0，煙氣毒性達到準安全三級。

　　Stone composite board: natural granite or marble combined with ceramic thin plates, with a fire resistance limit of over 2 hours. In the application of a high-rise residential project in Tai'an, the stone door frame has been specially tested by the fire department, and the flame spread index is 0, with smoke toxicity reaching quasi safety level three.

　　改性塑料：采用阻燃PC/ABS合金，氧指數達32%以上。某工地實驗室模擬火災場景，改性塑料門套在離火自熄，無熔融滴落現象，避免火勢縱向蔓延。

　　Modified plastic: Made of flame-retardant PC/ABS alloy, with an oxygen index of over 32%. A construction site laboratory simulated a fire scenario, where the modified plastic door frame automatically extinguished after leaving the fire without melting or dripping, avoiding the longitudinal spread of the fire.

　　二、工藝標準的防火保障

　　2、 Fire protection of process standards

　　密封結構：門套與墻體間隙填充防火密封膠。

　　Sealing structure: Fill the gap between the door frame and the wall with fireproof sealant.

　　防煙設計：門套頂部設置不銹鋼擋煙垂壁，與消防聯動系統配合，可在火災確認后自動下垂，形成有效防煙分區。

　　Smoke prevention design: The top of the door frame is equipped with a stainless steel smoke barrier wall, which, in conjunction with the fire linkage system, can automatically sag after a fire is confirmed, forming an effective smoke prevention zone.

　　耐火構造：門套轉角處采用L型防火角碼連接，經極限載荷測試，在300℃環境下保持連接強度，防止門套脫落形成煙囪效應。

　　Fire resistant construction: The corner of the door frame is connected with an L-shaped fireproof corner code. After ultimate load testing, the connection strength is maintained at 300 ℃ to prevent the door frame from falling off and forming a chimney effect.

　　三、泰安工地的實際應用驗證

　　3、 Practical application verification of Tai'an construction site

　　住宅項目案例：泰安某33層住宅樓電梯門套選用2.0mm厚鍍鋅鋼板包覆硅酸鈣板，經實體火災試驗，在60分鐘耐火試驗中，門套背火面平均溫升，未引燃周邊可燃物。

　　Residential project case: The elevator door frame of a 33 story residential building in Tai'an was covered with 2.0mm thick galvanized steel plate and calcium silicate board. After a physical fire test, the average temperature rise of the back fire surface of the door frame during the 60 minute fire resistance test did not ignite the surrounding combustibles.

　　商業綜合體實踐：某購物中心采用石材蜂窩復合門套，配合自動噴水滅火系統，在模擬火情中，門套表面溫度控制在，為人員疏散爭取時間。

　　Commercial complex practice: A shopping center adopts stone honeycomb composite door frames, combined with an automatic sprinkler fire extinguishing system. In simulated fire situations, the surface temperature of the door frames is controlled at to buy time for personnel evacuation.

　　工業廠房應用：某食品加工廠電梯門套選用改性酚醛樹脂板，在含油霧環境中，經消防部門專項檢測，閃點達，顯著降低次生火災風險。

　　Industrial plant application: The elevator door frame of a certain food processing plant uses modified phenolic resin board. In an oil mist environment, after special testing by the fire department, the flash point reaches, significantly reducing the risk of secondary fires.

　　四、防火性能的認證與維護

　　4、 Certification and maintenance of fire resistance performance

　　型式檢驗：正規廠家需提供國家防火建筑材料質量監督檢驗中心出具的檢測報告，重點核查燃燒增長速率指數、產煙毒性等關鍵指標。

　　Type inspection: Legitimate manufacturers are required to provide a testing report issued by the National Fire resistant Building Materials Quality Supervision and Inspection Center, with a focus on verifying key indicators such as combustion growth rate index and smoke toxicity.

　　現場驗收：安裝完成后需進行門套完整性測試，使用紅外熱像儀檢測縫隙處溫升，確保不超規范限值。

　　On site acceptance: After installation, a door frame integrity test is required, and an infrared thermal imager is used to detect the temperature rise at the gap to ensure that it does not exceed the specified limit.

　　維護管理：每半年檢查防火密封條彈性，使用測厚儀檢測門套基材厚度，腐蝕量超30%時需整體更換。

　　Maintenance management: Check the elasticity of the fireproof sealing strip every six months, use a thickness gauge to measure the thickness of the door frame substrate, and replace it as a whole when the corrosion exceeds 30%.

　　本文由泰安工地電梯門套友情奉獻.更多有關的知識請點擊:http://www.k2f3.com我們將會對您提出的疑問進行詳細的解答，歡迎您登錄網站留言.

　　This article is a friendly contribution from Linyi Elevator Door Frame Installation For more information, please click: http://www.k2f3.com We will provide detailed answers to your questions. You are welcome to log in to our website and leave a message